HGO2401603产品初始化代码

/******** 杭州清达光电、杭州佳显科技 液晶屏初始化程序 ********/

void Init()
{ 
  #if I80==1
    CONTROL1_OUTPUT_MODE();  //控制口1为输出 
    CONTROL2_OUTPUT_MODE();  //控制口2为输出
    CONTROL3_OUTPUT_MODE();  //控制口3为输出
    CONTROL4_OUTPUT_MODE();  //控制口4为输出
  #endif     
    
     IF2_L;IF1_H;IF0_H;
     
     delay(20);  
     REST_L;
     delay(20);  
     REST_H;
     delay(50);  


  /******************************
***   Extension Command 2 
******************************/
write_com(0x31); // Extension Command 2 
write_com(0xd7); // Disable Auto Read  
write_data(0x9f);


write_com(0xe0); // Enable OTP Read
write_data(0x00); // 
delay(10);
write_com(0xe3); // OTP Up-Load 
delay(20);; // 
write_com(0xe1); // OTP Control Out


/******************************
***   Extension Command 1 
******************************/
write_com(0x30); // Extension Command 1
write_com(0x94); // Sleep Out
write_com(0xae); // Display OFF
delay(50); 


write_com(0x20); // Power Control 
write_data(0x0b); // VB, VR, VF All ON


write_com(0x81); // Set 
write_data(0x2d); //给定初值0x37  //   0x1d:Vop = 15.5V 
write_data(0x04); // 


/******************************
***   Extension Command 2 
******************************/
write_com(0x31); // Extension Command 2 
write_com(0x32); // Analog Circuit Set  
write_data(0x00); // 
write_data(0x00); // Booster Efficiency =6KHz 
write_data(0x01); // Bias=1/12 


/******************************
***   Extension Command 2 
******************************/
write_com(0x31); // Extension Command 2 
write_com(0x49); //  HPM=1; 
// 

write_com(0x51); // Booster Level x8
write_data(0xfa); // 



/******************************
***   Extension Command 1 
******************************/
write_com(0x30); //  Extension Command 1 
write_com(0xf0); //  Display Mode 
write_data(0x10); //  Mono Mode 


write_com(0xca); //  Display Control 
write_data(0x00); // CL Dividing Ratio ?  Not Divide
write_data(159); // Duty Set   128 Duty 
write_data(0x0C); // Frame Inversion 


write_com(0xbc); //Data Scan Direction
write_data(0x00); //  seg0-seg240   com0-com159
 

write_com(0xa6); // 3.Inverse display:a6=normal,a7=inverse
write_com(0x0c); //26.Data Format Select DO=0(0x08); LSB on bottom (Default) ; DO=1(0x0c); LSB on top 



/******************************
***   Extension Command 2 
******************************/
write_com(0x31); //  Extension Command 2  
write_com(0xf0); //SET Frame Rate   HZ
write_data(0x00); 
write_data(0x09);
write_data(0x09);   

write_data(0x0b);  

write_com(0xf4); //SET Temperature Compensation 
write_data(0x00);   
write_data(0x00);
write_data(0x00); 
write_data(0x03); 




/******************************
***   Extension Command 1 
******************************/
write_data(0x30); //old 0x50   
write_data(0x50); //old 0xb0
write_data(0x84); 
write_data(0x05); 

write_com(0x40); //  Internal Power Supply  


/******************************
***   Extension Command 2 
******************************/
write_com(0x30); //  Extension Command 1 
write_com(0xaf); //  Display ON 

}

需要其他液晶驱动测试程序可来电咨询，也欢迎选购我司的各种尺寸点阵液晶模块产品哦~~

qdgdlcd.b2b168.com/m/